Join Our Ford Truck Forum Today

Document your Ford truck project here and inspire others! Login/Register to view the site with fewer ads.

Search results

  1. Sparky83

    Grandpa's Truck

    Looking good. Keep up the good work there
  2. Sparky83

    Got a new 2002 Gen.10

    Nice and clean there.
  3. Sparky83

    1994 f350 (7.5L) dropping out of gear

    Im hoping one of the members here more versed in the older trucks will chime in and help. All i was able to find were the codes. I know low trans fluid levels can cause wonky shifting. But figured you would have already checked that since you had just done the solenoid pack. And if your...
  4. Sparky83

    1994 f350 (7.5L) dropping out of gear

    Code 67 - Service Code 67 indicates that during Self-Test, voltage was high on NDS (Pin 30) or ACCS (Pin 10) circuit.Code 21 - indicates the transmission wasnt run up to temp before self tests were run.Code 41 - its a lean emissions code. Right bank supposedly. Which can cause misfires if...
  5. Sparky83

    Need help with a Mac tool box

    Thats a bummer man. The snapon guy in my areas kinda a D... I know a few techs in the area hes screwed over on warranty stuff simply because he didnt want to deal with it. Some of the shops asked him not to come back.
  6. Sparky83

    Need help with a Mac tool box

    Mac tends to warranty their stuff pretty well. Might be able to call them and have them come look at it.
  7. Sparky83

    Odd turn signal issue

    Double check your fuses. When i got my truck i found that the po replaced many with the wrong sizes. Had to go through with the om and replace almost half with the correct sizes.
  8. Sparky83

    1996 Ford F350 XL one ton dually with 8 foot service bed

    Was going to say the same. Price of the truck is a pretty good deal for what ive seen lately.
  9. Sparky83

    Engine flush

    Sorry for late reply been busy lately with life. But as far as flushing. Ive known some people that swear by flushing the coolant passages with things like "Rad flush" you can find in most stores on the shelf or fords thing (forget what its called atm). And others that dont. Personally i just...
  10. Sparky83

    Fuel pump relay and inertia switch wires melted

    I dont know about the 88. But i know on my 04 stang it goes from relay to what they call a fuel pump control module. Then to the inertia switch and then to the pump. The control module regulates the voltage to the pump to vary the speed and pressure. But your case definitely sounds like...
  11. Sparky83

    Rough idle, harder start, several codes...

    P0475 - back pressure control module malfunctionP0500 - Failed vehicle speed sensor. Open or short in the wiring harness.P1832 - another transmission code concerning the pressure control moduleP1876 - transmission control moduleB1203 - fuel sender shorted to batteryB1318 - battery low...
  12. Sparky83

    Hi my name is Donald

    Howdy.
  13. Sparky83

    Hello

    Welcome to the site
  14. Sparky83

    Hi all

    Welcome to the site.
  15. Sparky83

    New to forum and workin on my truck!

    Almost sounds like a ground issue. The old printed boards used to lose the ground and never read over half a tank. But your 13 would have soldered boards.
  16. Sparky83

    New to forum and workin on my truck!

    Welcome to the site. Sorry about your woes with the truck. My guess would be somethings been pinched. I know fords had some issues with fuel level readers being off. Mines had that issue a few times. Itll say its at 1/4-1/2 tank when its actually full. Usually fixes itself after 30 mins of...
  17. Sparky83

    HELLO I'm Pa Pitt

    Welcome to the site!! Im going to guess from your user name your from Pittsburgh??
  18. Sparky83

    Jim from Oregon

    Welcome to the site trapper
  19. Sparky83

    Newbie

    Welcome to the site
  20. Sparky83

    Check Engine 2002 f-250 super duty

    Since you already bought the cleaner. Would go ahead and use it. Sometimes it works. If not can still replace it
  21. Sparky83

    hello from Wisconsin

    Welcome to the site
  22. Sparky83

    Greetings From The Bay Area

    Howdy. Welcome to the site
  23. Sparky83

    1978 Intermittent wiper conversion

    That part i cant answer. It was just what i could find online for the same sounding condition. But they were factory installed units. So dont know how the conversion units act. I know when my dad tried to do the same with the corsica we had at the time it wouldnt work at all.
  24. Sparky83

    1978 Intermittent wiper conversion

    Everything i could find for it said the relay tends to be the problem when just the intermittent stops working. The only other mention is a failed circuit board in the wiper motors or bad contacts at the wiper motor.Circuit board on the motors was mentioned with newer vehicles so dunno if...
  25. Sparky83

    1978 Intermittent wiper conversion

    Did the intermittent conversion contain a relay??
  26. Sparky83

    hey hey

    Welcome to the site.
  27. Sparky83

    Hello

    Welcome to the site. Got any pics??
Top